- LEGS -

MOUNTING & FITTINGS

For our legs there are 2 different fitting options: M8 bolt and/or Universal mounting plate.


M8 BOLT

Always included and fits a large number of furniture types, see listed IKEA furniture below, all compatible with M8 bolts.

.........

SOFAS: 
Karlstad, Klippan, Karlsfors, Klobo, Mysinge, Ektorp, Söderhamn, Solsta, Ljungvik, Sandby, Oleby, Tidafors, Vaxholm, Härnösand, Skogaby, Säter, Ystad, Landskrona, Dagarn, Norsborg, Stockholm (up to 3 seat), Stockholm 2017 (up to 2 seat), Vallentuna (does not fit the sofa bed), Vimla

ARMCHAIRS: 
Mellby, Tullsta, Solsta-Olarp, Karlstad, Karlsfors, Strandmon, Ekenäs, Muren, Skogaby, Söderhamn, Ystad, Landskrona

FOOTSTOOLS: 
Karlstad, Karlsfors, Klippan, Strandmon, Stocksund, Skee, Söderhamn, Ystad, Landskrona, Dagarn

STORAGE: Bestå

NOTE: There might be furniture models within the furniture series listed above that are not compatible with M8, so please check that your furniture has pre-drilled holes for bolts. If not, you can always add our Universal mounting plate, see below.

.........

How to attach Prettypegs legs with M8 bolt:

1 Screw the bolt down in the leg until it sticks out 2-3 cm.  
2 - 
Attach the legs directly into the furniture's threaded M8 holes

..........................................................................................

UNIVERSAL MOUNTING PLATE

For furniture that do not support M8 bolts, our Universal plates fit most corner frames for sofas, chairs, beds, storage furniture etc.

Our universal plate can be attached either on a flat wooden surface or in a corner frame. Always check that the surface where the legs shall be placed can take small screws.

Universal plates will automatically be added to your order if you choose "Other furniture" at the product page.

16mm screws will be included and will be sufficient for most furniture. However you can always use thicker, longer screws if the material is dry or porous.

.........

How to attach Prettypegs legs with Universal mounting plate:

1 - Attach the plate with small screws in the corners of your furniture.
2 - Screw the bolt down in the leg until it sticks out about 0,5 - 1 cm.  
3 - Attach the legs to the Universal plate by hand.   





IMPORTANT NOTES:

- As with all furniture legs - remember to put felt pads on to protect your floor (included). 

- Be cautious when turning over your furniture not to bend the legs or damage the floor. Our advice is to always be two persons when mounting legs at larger furniture.

- We do not recommend Prettypegs for sofa-beds since the foldable bed legs usually are not replaceable nor adjustable in height.

- When attaching Prettypegs to storage furniture, for example Ikea Bestå, make sure to screw down the bolt into the leg until it is visible only 1,5-2 cm, not to risk the bolt being screwed through the board where legs are mounted.

- If the material in your furniture feels dry or porous, it might be necessary to use longer and thicker screws (than the ones included) to fix the Universal plates properly.

..........................................................................................

- KNOBS -

MOUNTING

Our knobs come with M4 bolt and fit most storage furniture with pre-drilled holes for knobs.

If you need to drill new holes to fit knobs, please make sure to measure and mark where the hole should be drilled, our recommendation is to follow the instructions below.

.........

How to attach Prettypegs knobs:

1 - Place the hole 4-5cm from each side of the corner.

2 - Drill a hole from the outside of the door with a 4-5mm thick drill. 

3 - Place the knob on the outside of the door and screw the supplied screw from the inside of the door in to the knob.

(Note: Make sure not screw the knob to attach it. Only screw the M4 bolt from the backside of the door)

..........................................................................................

- FRONTS -

Our superthin, self adhesive wooden layers are made to fit the doors of IKEA Bestå´s most popular storage sizes:

600 mm x 260 mm / 23 5/8" x 10 1/4 "
600 mm X 380 mm / 23 5/8 " x 15 "
600 mm X 640 mm / 23 5/8 " x 25 1/4 "

.........

How to attach Prettypegs fronts to your IKEA bestå furniture:

1 - Gently remove the thin protection film from the backside of the front sheet.

2 - Attach the front sheet directly onto the door of your Bestå storage. Make sure the surface of the furniture is clean and dry.

NOTE: If you need to ajust the front sheet, it is possible to rip it off and apply a second time. However, this is not to be adviced since it could damage the surface of your furniture.

..........................................................................................

You are always welcome to contact us for any questions! - hello@prettypegs.com


Back to Top